InterNACHI® Certified Professional Inspectors · Clermont, FL

Four Corners Inspection Services — Same team. Same 5-star service.

Professor Elias Walls teaching a class of homeowners in the Four Corners Knowledge Center classroom

Siding on Florida Homes: Beyond Stucco

Professor Elias Walls · Educational Contributor, Four Corners Knowledge Center

15 min read

Lesson 1 of the Exterior Protection series. Fiber cement (Hardie), vinyl, engineered wood, wood, brick, and stone veneer on Central Florida homes: how each is built to shed water, what the Florida code requires, and the defects buyers should know.

Professor Elias Walls, the Four Corners Knowledge Center teacher

The Exterior Protection Series, Lesson 1 · A New Series Begins · Taught by Professor Elias Walls · Researched and reviewed by Grant Doutt, Certified Master Inspector®

🎓 The Professor's Quick Answer

Most Central Florida homes are block and stucco, but plenty of them also wear siding: fiber cement (Hardie is the best-known brand) on framed second floors and gables, vinyl on older frame homes and additions, engineered wood, the occasional real wood cottage, and accents of brick or stone veneer. Each can last decades in Florida, and each fails the same way: water gets behind it and stays there. Some older homes may still have asbestos-cement siding: leave it alone and have professionals test it.

The key idea is that no siding is waterproof. On a framed wall, the 2023 Florida Building Code treats the siding as the first layer only. Behind it, the code requires a water-resistive barrier and flashing that carry any water that gets past the siding back outside. The details that keep it working: 6 inches of clearance to the soil, flashing where roofs meet walls, sealed cut ends, and fasteners installed exactly as the manufacturer says. On wood-frame walls, which we're seeing more of on new homes, those details carry even more weight.

🏫 Welcome Back to the Knowledge Center

Professor Elias Walls, the Four Corners Knowledge Center teacher

Last class we walked the walls with a ruler and learned to read stucco cracks. That wrapped up our Foundations series. But maybe you noticed on that wall walk: not every wall on a Florida house is stucco.

Drive through a new neighborhood in Clermont or Minneola and look up: lap siding or board-and-batten on the gables, stone around the entry columns. Today begins a short two-part series on exterior protection, the skin of the house, and we start with everything that isn't stucco.

🏠 Why So Many Florida Homes Aren't All Stucco

As we saw in Lesson 4, most Central Florida homes have concrete block walls with stucco applied right to the block. But many mix in wood framing, which gets either stucco over lath or siding. You'll find siding in a few predictable places:

  • Framed upper floors and gables on newer two-story homes, often fiber cement over a block first floor.
  • Older frame homes, from 1920s cottages to 1970s ranches, with wood, hardboard, or vinyl.
  • Additions, enclosed porches, and garages built later in wood frame.
  • Accent walls and wainscots of brick or manufactured stone at entries, columns, and garage fronts.

💧 The Big Idea: Siding Is a Rain Screen, Not a Raincoat

Wind-driven rain gets past every siding product made, through laps, joints, and the edges around windows. The building code plans for it.

Section R703.1.1 of the 2023 Florida Building Code, Residential, says the exterior wall must prevent water from building up inside the wall by providing a water-resistive barrier behind the cladding and a way for water that gets past the cladding to drain back out. Section R703.2 requires at least one layer of water-resistive barrier over the studs or sheathing, lapped like shingles. That's the housewrap you see on framed walls.

Then comes flashing (R703.4), which steers water out where it collects: window and door openings, the tops of projecting trim, wall-and-roof intersections, and where decks attach to a framed wall.

Two connections to earlier lessons:

  • Block walls are different. The code doesn't require a barrier over properly flashed concrete or masonry walls, one reason stucco goes straight onto block. Some siding makers, LP among them, still require a drainable wrap over block.
  • Stucco over frame asks for more. Last class, stucco over wood sheathing needed the equivalent of two layers of Grade D paper. Siding needs at least one.

🧰 Fiber Cement: The Florida Favorite

Fiber cement is made of portland cement, sand, and cellulose fiber, pressed into planks, panels, shingles, and trim. James Hardie is the brand most people know, and many people say "Hardie board" for any fiber cement. The code calls for it to meet ASTM C1186 (R703.10), and lap siding must overlap at least 1¼ inches.

It doesn't rot like wood, Hardie markets it as termite-resistant, and Hardie's HZ10 version is made for hot, humid climates, with a 30-year limited warranty that depends on following the instructions. They require:

  • Ground clearance. At least 6 inches between the siding and the finished grade.
  • Roofs, paths, and driveways. A 1- to 2-inch gap where siding meets a roof, deck, walkway, or driveway.
  • Kickout flashing. Where a lower roof runs into a sidewall, a kickout of at least 4 by 4 inches turns water away from the siding. Our lesson on where roofs really leak explains why a missing kickout is a classic cause of hidden wall rot.
  • Cut edges sealed. Every field-cut edge gets caulked, painted, or primed.
  • Paint on time. Factory-primed boards must be painted within 180 days, with 100% acrylic paint. No stain, and no oil-based paint.

Practice varies on nailing. Hardie publishes wind-load tables for both blind nailing (hidden under the next board) and face nailing, while FEMA's coastal guidance favors face nailing where design wind speeds reach 100 mph, which covers Central Florida. Either can meet code when it follows the tables.

🏡 Vinyl Siding: Can You Use It in Florida?

Professor Elias Walls, the Four Corners Knowledge Center teacher

Yes, with conditions. The code requires vinyl certified to ASTM D3679 (R703.11), installed per the manufacturer's instructions, and siding falls under Florida's Product Approval system (Rule 61G20-3), so the product should be approved for the wind pressures it will face.

Vinyl's first rule surprises people: it has to hang loose. It grows and shrinks with temperature, so the Vinyl Siding Institute's manual says:

  • Nail in the center of the slots, and leave about 1/32 inch (the thickness of a dime) between the nail head and the siding.
  • Leave at least 1/4 inch at J-channels, corners, and openings for expansion.
  • Don't caulk the laps, corners, or channels, and don't face-nail through the panels.

Nail it tight and the panels buckle in summer heat. The manual is also blunt that vinyl is cladding, not a water-resistive barrier. Florida problems we see:

  • Wind damage. Panels unzip or blow off when the wind rating or fastening falls short; FEMA recommends high-wind-rated products with reinforced nailing hems.
  • Heat distortion from reflected window sunlight or a nearby grill.
  • Impact cracks from mowers and storm debris.

🌲 Engineered Wood and Real Wood

Engineered wood siding, with LP SmartSide the best-known brand, is wood strands treated with zinc borate, waxes, and resin binders under a resin-saturated overlay. LP's instructions call for 6 inches above grade, 1 inch above walks and roofs, every cut end sealed, and primed boards painted within 180 days, with a 50-year limited, prorated substrate warranty.

LP's newest siding is mostly about finish and profile. Its factory-prefinished SmartSide ExpertFinish line, launched in 2020, added the wood-toned Naturals Collection in 2025 and, in April 2026, the Coastal Capsule, six brushed-smooth colors offered from North Carolina through Florida and the Gulf Coast. In September 2026, LP added a primed 8-inch Brushed Smooth Shake Lap Siding for gables and accents.

Some hardboard and early strand-board siding sold in the 1980s and 1990s swelled and rotted when wet, leading to national class-action settlements.

Real wood siding, often cypress or heart pine on older cottages, can last a century when painted and kept off the ground. Its enemies: rot at bottom courses and under windows, termites (see Lesson 2), and peeling paint that lets water in.

T1-11 Panel Siding on Gable Ends

T1-11 (APA calls it Texture 1-11) is grooved plywood panel siding, rated APA 303 Siding, with grooves usually 4 or 8 inches apart; overlaid OSB versions look similar. On Central Florida homes, Four Corners sees it most often on the gable ends of block homes, where the framed triangle above the block wall gets 4-by-8 panels instead of stucco, and on older frame homes and additions.

What the code and APA call for:

  • Joints. Vertical joints land on framing and are shiplapped or battened. Horizontal joints are lapped at least 1 inch, shiplapped, or Z-flashed over solid blocking (R703.5.2). APA recommends a 1/8-inch gap at panel edges and ends.
  • Sealed edges. Seal every panel edge, especially the bottom drip edge, and reseal any cut edge.
  • Barrier and clearance. A water-resistive barrier behind it, at least 6 inches to the soil, and flashing where walls meet roofs.
  • Finish on time. APA recommends the first coat within two weeks, acrylic latex paint or solid-color stain, and refinishing when bare wood or peeling first shows, usually on south and west walls.

Rated panel siding nailed to APA's schedule can also brace the wall (APA's Sturd-I-Wall system), so a badly rotted panel can mean more than a cosmetic patch.

What we find: delamination and swelling at bottom edges and horizontal joints, missing Z-flashing between upper and lower panels, rot where a gable wall meets a lower roof, and peeling finish on the sunny sides.

⚠️ Asbestos-Cement Siding on Older Homes

Some older Central Florida homes still wear asbestos-cement siding: portland cement reinforced with asbestos fibers, common from roughly the 1920s into the 1980s. EPA lists asbestos-cement siding shingles among the asbestos products found in older homes.

Clues that siding may be asbestos-cement:

  • Era. A home built or re-sided before the early 1980s.
  • Shape. Rigid shingles, often about 12 by 24 inches, or flat panels, sometimes with a wavy bottom edge.
  • Texture. A molded wood-grain, dimpled, or stippled face.
  • Nails. A row of exposed nail heads through pre-punched holes near the bottom of each shingle.
  • Feel. Thin, hard, and brittle, with chipped corners; it doesn't bend like vinyl or dent like aluminum.

Modern fiber cement can look much the same, and EPA says asbestos usually can't be identified visually: only an accredited lab's analysis of a professionally taken sample can confirm it.

Leave it alone. EPA's advice is that asbestos material in good condition is best left undisturbed, and that asbestos-cement products aren't likely to release fibers unless sawed, drilled, or broken. Don't drill, sand, cut, scrape, pressure-wash, or break it.

Removal is for professionals. Florida licenses asbestos consultants, who survey and plan, and asbestos contractors, who remove and dispose, under Chapter 469, Florida Statutes. The law has a narrow exemption for an owner who lives in the home, isn't selling or leasing it, and personally signs the permit under owner-builder limits, but that doesn't make the work safe. The federal asbestos NESHAP (40 CFR Part 61, Subpart M) and Florida DEP's 10-working-day demolition and renovation notice (Rule 62-257) generally exempt a single home with four or fewer units, unless it's part of a larger project, was used commercially, or is cleared for a commercial building. Talk to your building department and a licensed professional before any work.

🧱 Brick and Stone Veneer

In Central Florida, brick and stone are usually veneers: a decorative layer in front of a block or framed wall, not the structure.

Anchored brick veneer (R703.8) is real brick tied back to the wall with metal ties. Over framing, the code calls for a nominal 1-inch air space behind the brick, a water-resistive barrier on the wall, flashing under the first course above grade, and weep holes right above that flashing, no more than 33 inches apart and at least 3/16 inch across. Mortar dropped into the air space blocks that drainage.

Adhered manufactured stone veneer (R703.12) is lightweight concrete set in mortar, the stone on columns and wainscots, installed to ASTM C1780 or the manufacturer's instructions. On framed walls, it must stop at least 4 inches above soil, 2 inches above paving, or 1/2 inch above a walking surface on the same foundation, with a weep screed or flashing at the bottom, and the same two-layer barrier stucco gets over wood.

Over clean block, the Masonry Veneer Manufacturers Association's guide allows direct application; over framing, trapped water can damage sheathing.

Common veneer defects:

  • Weeps missing, painted over, or buried under mulch, pavers, or soil.
  • Stone run straight down into the ground with no screed or clearance.
  • Cracks where stone meets stucco or siding, which move differently.
  • Rusting steel lintels over openings in brick, which can crack the brick above.

🏗️ Block vs. Frame: What's Going Up Today

On new homes, Four Corners is seeing a lot of wood framing right now, especially around the Sugarloaf Mountain area of Lake County, north of Clermont and Minneola, most often with LP siding or Huber's ZIP System sheathing. Here's what the research says, from both sides:

  • National data favor wood. NAHB's analysis of 2025 Census data found concrete framed 9% of new single-family homes completed in the South, down from 17% in 2019, and wood framed 94% nationally.
  • The block industry reports the opposite locally. The masonry industry's Block Strong campaign reports block's Florida share rising from 65% to 72% between 2021 and 2023, and about 80% in Central Florida. Those are industry figures, not Census data.
  • Cost and labor push frame. The Wall Street Journal reports wood-framed homes are cheaper and faster to build, while Florida's skilled-trades shortage stretches schedules.
  • Stucco still leads the finish. NAHB found stucco on 33% of new homes started in 2025 in the South Atlantic division, which includes Florida.

Can frame be as strong as block? The code doesn't pick a winner: both must be designed for the site's wind loads, and frame relies on a continuous load path of straps, hold-downs, and structural sheathing from roof to foundation. IBHS's voluntary FORTIFIED Gold designation requires that load path, designed by a licensed professional. After Hurricane Ian, IBHS found none of 455 single-family homes built to the modern Florida code had structural wind damage, but siding, soffits, and roof coverings still failed, and Florida's product approval worked less well for siding than for windows and doors. Marketing on both sides claims more than that evidence shows. On a frame wall, the siding and the barrier behind it are what keep the rain out.

Sheathing with the barrier built in. ZIP System and LP's WeatherLogic Air & Water Barrier are structural OSB panels with a factory-bonded water-resistive overlay; Georgia-Pacific's ForceField OSB and DensElement gypsum sheathing work the same way. All four hold Florida Product Approvals as combined sheathing and barriers. They aren't siding. They replace housewrap under R703.2 only when installed per their evaluation reports, with every seam sealed using the maker's tape or liquid flashing, and Huber and LP say that behind stucco or stone, which need two layers, the panel counts only as the first.

🌀 Wind, Sun, and Sprinklers: The Florida Stress Test

Professor Elias Walls, the Four Corners Knowledge Center teacher

Wind. Section R703.1.2 requires wall coverings and fasteners to resist the house's design wind loads; above 30 pounds per square foot, attachment must be designed (R703.3.1). After a storm, look for loose or missing pieces.

Sun. UV breaks down paint and sealant, so repainting on schedule is maintenance, not decoration.

Water from below. The code wants the ground to fall at least 6 inches in the first 10 feet from the foundation (R401.3). Climbing mulch, pavers tight to the wall, and sprinklers hitting the siding keep the bottom courses wet, where most damage starts.

Termites. Section R318.7 requires at least 6 inches between wall coverings and the earth so termite tunnels can be seen. Bury the siding and you've hidden the evidence.

🔍 Telltale Signs: A Buyer's Siding Checklist

When you tour a home with siding, look for:

  • Clearance. At least 6 inches between soil or mulch and the siding, and no siding sitting on a roof or driveway.
  • Kickouts where lower roofs meet sidewalls, with solid siding below them.
  • Bottom edges. Swelling, soft spots, or peeling paint along the lowest courses and below windows.
  • Joints and shape. Open joints, wavy vinyl, or cracked fiber cement near nails.
  • Gable panels. Swollen or delaminated T1-11 edges, missing Z-flashing, or peeling paint.
  • Veneer. Visible weep holes and stone held off the ground.
  • Era. Brittle shingles with nail rows on an older home: treat them as suspect asbestos-cement.
  • Inside. Stains or bubbling paint on exterior walls.

🧭 What We Check During the Inspection

Florida's home inspection Standards of Practice have us inspect the exterior wall cladding, flashing, and trim and describe the siding (Rule 61-30.810), and inspect grading and drainage when they're likely to affect the structure (Rule 61-30.811). We report what we see; we don't take walls apart.

Here's what we do:

  • Describe the cladding on each wall.
  • Walk every wall, noting clearances, damage, gaps, buckling, and failed paint or sealant.
  • Look at visible flashing where roofs meet walls and above openings, including kickouts.
  • Check the water side: grading, downspouts, and sprinkler spray, using infrared scanning where conditions allow to flag patterns consistent with moisture, plus a moisture meter where we can reach.
  • Look inside for stains on exterior walls.

We can't see the barrier, sheathing, or framing behind finished siding. When conditions suggest water is getting in, we recommend evaluation by a qualified siding contractor.

If siding looks like it may be asbestos-cement, we note it as suspected asbestos-containing material. We don't sample or test for asbestos, and we aren't asbestos consultants; Florida's Standards of Practice exclude environmental hazards (Rule 61-30.812). We recommend a licensed asbestos consultant or contractor and lab testing before anyone disturbs it.

For new homes, siding issues belong on your blue tape walk and, after a year of sun and storms, your 11-month warranty list. Our new construction inspections run from pre-drywall to 11 months, and our home inspections serve buyers in Lake County, Winter Garden, Orlando, Kissimmee, Polk County, and The Villages.

❓ Questions From the Back Row

"Is Hardie board better than vinyl siding in Florida?"

Both can perform well. Fiber cement resists impact and heat better but needs paint. Vinyl never needs paint but must carry the right wind rating and hang loose. Installation matters more than the label.

"Is a wood-frame home as strong as a block home?"

Both must be engineered for Florida wind loads, and modern code-built homes of both kinds performed well structurally in Hurricane Ian. Frame depends on its straps and sheathing; ask for the permits and plans.

"Can I pressure wash my siding?"

Check the manufacturer's care instructions. A garden hose and soft brush are safest; a high-pressure stream aimed upward drives water behind laps.

"Should I caulk every gap in my siding?"

No. Vinyl joints must stay uncaulked so panels can move, and some fiber cement flashing gaps stay open to drain. Caulk only where the instructions call for it.

"Is the old cement siding on my house asbestos?"

It might be, if the home is older. Only a lab test of a professionally taken sample can tell you. Until then, leave it undisturbed.

🚌 Field Trip — Class Dismissed

Your homework: a siding walk. On each wall, measure from the soil or mulch to the bottom of the siding and photograph anything under 6 inches. Look for a kickout wherever a lower roof meets a wall, feel the bottom courses for soft spots, and run the sprinklers to see where they spray. Students who find the wet spots before the termites do always pass this course.

Next class, the series finale: fascia, soffits, and the ornamental trim. The coverings over your fascia and soffits, why vented soffits matter to your attic, and the decorative bands and window surrounds on so many Florida homes: what they're made of, including Styrotrim foam trim, and how to protect them with your siding.

Sources: 2023 Florida Building Code, Residential (8th Edition, in effect until the 9th Edition (2026) takes effect December 31, 2026), Sections R318.7, R401.3, R703.1, R703.1.1, R703.1.2, R703.2, R703.3.1, R703.3.5, R703.4, R703.5 (R703.5.2), R703.7.3, R703.8 (R703.8.4, R703.8.4.1, R703.8.5, R703.8.6, Table R703.8.4(1)), R703.10, R703.11 and R703.12; Florida Administrative Code Rules 61-30.810, 61-30.811, 61-30.812, 61G20-3 (Florida Product Approval) and 62-257 (asbestos notification); Florida Statutes Chapter 469 (Asbestos Abatement), including s. 469.002; EPA asbestos NESHAP, 40 CFR Part 61, Subpart M, and EPA homeowner asbestos guidance; Florida DEP Asbestos Program FAQ (residential exemption); NAHB, Exterior Material Trends in Single-Family Homes (July 2026) and Wood Framing Continues to Dominate Single-Family Construction (September 2026), both on U.S. Census Bureau data; U.S. Census Bureau, Characteristics of New Housing, Type of Framing; Block Strong campaign figures as reported by Aggregates Business; The Wall Street Journal, "In Hurricane-Prone Florida, Builders Are Still Making New Homes Out of Wood"; IBHS, Building Performance in SW Florida During Hurricane Ian, Part II, and IBHS Continuous Load Path / FORTIFIED Home; Huber ZIP System Wall Sheathing installation manual and ICC-ES ESR-1474 (Florida Product Approval FL17147); LP WeatherLogic Air & Water Barrier Installation Manual and APA Product Report PR-N138 (FL30464); Georgia-Pacific ForceField (APA PR-N136; FL19689) and DensElement Barrier System (ICC-ES ESR-3786; FL12807); LP news releases on SmartSide ExpertFinish Naturals Collection (April 2025), Coastal Capsule (April 2026) and 8-inch Brushed Smooth Shake Lap Siding (September 2026); James Hardie HardiePlank HZ10 Installation Instructions and Best Practices Installation Guide; Vinyl Siding Institute (Polymeric Exterior Products Association) Vinyl Siding Installation Manual; LP SmartSide Application Instructions and Technical Bulletin No. 0001; APA Product Guide: Performance Rated Siding (Form E300), APA Engineered Wood Construction Guide (Form E30, including the Sturd-I-Wall system) and APA typical detail, Z-Flashing Installation, APA Rated Siding; Brick Industry Association Technical Note 28; Masonry Veneer Manufacturers Association, Installation Guide for Compliance with ASTM C1780; FEMA P-499, Home Builder's Guide to Coastal Construction, Technical Fact Sheet No. 5.3, Siding Installation in High-Wind Regions. Building practices vary by builder, era, and product; any specific home should be evaluated on its own plans, products, and condition.

Buying a home in Clermont, Lake County, or anywhere in Central Florida? Call or text (352) 272-1322 or visit fourcornershomeinspections.com.

Taught by Professor Elias Walls · Researched and reviewed by Grant Doutt, Certified Master Inspector® · Last reviewed: November 2026. Professor Elias Walls is the teaching persona of the Four Corners Knowledge Center. Every lesson is researched, written, and fact-checked by the licensed, certified inspectors of Four Corners Inspection Services.

← All Knowledge Center lessons

Ready for Peace of Mind?

Whether you’re buying your dream home or making a smart investment, Four Corners Inspection Services is here to give you clear answers and confidence in your decision.

  • InterNACHI Certified Professional Inspectors
  • Residential & Commercial Inspections
  • Same-Day Digital Reports
  • Legendary Service ~ Beyond the Inspection
Book an Inspection Call Text us